Powder coated steel construction
Higher seat back for greater comfort
Includes generous footrest
All Items can he shipped FedEx
Deck Improvements will not warp
New space filler on flip-flop and new storage bin available(optional)
Will accept E-Z-GO and Club car 2000-UP existing top supports
OEM style seat covers with matching welt pattens and colors
Easy to install, improved hardware package, new slotted holes
E-Z-GO and Club Car come complete In three boxes instead of four

Example of installation

E-Z-GO 4-Passenger Flip Flop Seat Kit 1994-UP MED/TXT Installation Instructions
	Notes:	Bill of Material is shown on Page 2.  Quick Install Guide is shown on Page 2.
	1.Remove top canopy, keeping rear struts attached to the canopy. - Keep strut hardware at front for use with 80" top (80" kit required). - OR - - Keep strut hardware at front & rear for use with standard top. 2.Remove seat back cushion from bag rack/sweater basket assembly and keep  hardware for use in Step 4 below. 3.Remove bag rack/sweater basket assembly from vehicle. 4.Using the items from Step 2, loosely assemble the seat back cushion to the  Seat Back Support Brackets. See Figure 1. Note: These brackets are specific to each side of the vehicle and they have markings to indicate this. 5.Install the items from Step 4 to the vehicle. Tighten loose hardware from Step 4. Use:           Hardware Bag #5 with 9/16" long socket. 6.Using drill, drill through outer rivets in bag well. See Figure 2. Use:             7/16" or 10mm drill bit. 7.Install Footplate & Vertical Supports at the same time, using the enlarged  holes from Step 6. See Figure 3. Push Footplate flush against bumper. Note: If Safety Bar was purchased, you must first install this to the Footplate (with 14mm socket).
	Use: ** TIP'	Hardware Bag # 2 (hex bolts) with 17mm sockets.
	Use a floor jack to assist in the positioning of the Footplate. 8.Install Flip Flop Frame to Seat Back Support Brackets & Vertical Supports.  See Figure 4 for a view of the final assembly. Use:           Hardware Bag # 3 with 17mm socket & wrench. 9.Install Hand Rails to the sides of Flip Flop Frame. See Figure 4. Use:           Hardware Bag # 2 with 17mm wrench & #3 Phillips screw driver. 10.Install Hand Rails to the sides of Footplate. See Figure 4. Use:           Hardware Bag # 1 with 17mm sockets. 11.Install Rear Seat Back Bracket between Hand Rails. See Figure 4. Use:           Hardware Bag # 2 with 17mm socket & #3 Phillips screw driver. 12.Install Seat Back Cushion. Use:           Hardware Bag # 4 with 10mm socket. 13.Position Seat Bottom Cushion using (2) existing pilot holes in Seat Bottom  Cushion and (2) wood screws. Note: Make sure the pull strap is not trapped under the cushion. Using drill, drill (6) additional pilot holes into Seat Bottom Cushion and then complete installation. Use:             1/8" or 3mm drill bit. Hardware Bag # 6 with #2 Phillips screw driver/drill bit. 14.Install top canopy using hardware from Step 1.

E-Z-GO 4-Passenger Flip Flop Seat Kit

1994-UP MED/TXT

Installation Instructions

Bill of Material

(2) Seat Back Support Brackets - Driver & Passenger

(1) Footplate

(2) Vertical Supports

(1) Flip Flop Frame

(2) Viand Rails

(1) Rear Seat Back Bracket

(1) Seat Back Cushion & (1) Seat Bottom Cushion

(1) Box of Hardware - BOM shown below

		Bag#1	Bag #2	Bag #3	Bag #4	Bag #5	Bag #6
(2) M10-1.5 x 70 shoulder hex bolts	2
(2)M10-1.5x50hexbolts			2
(8) M10-1.5 x 50 Philips truss head bolts			8
(4)M10-1.5x25hexbolts					4
[361M10 washers	4	20	8			4
(16) M10-1.5 nylon lock nuts	2	10	4
(4) M6-1 .Ox 45 hex bolts							4
(4) M6 washers							4
(413/8M6 x 1.0" hex bolts								4
(8) wood screws									8

Quick Install Guide

Hardware Bag #1 Install Hand Rails to the sides of Footplate [Page 1, Step 10]

Hardware Bag #2 Install Footplate & Vertical Supports (hex bolts) [Page 1, Step 7] 
Install Hand Rails to the sides of Flip Flop Frame [Page 1, Step 9] 
Install Rear Seat Back Bracket between Hand Rails [Page 1, Step 11]

Hardware Bag #3    Install Flip Flop Frame to Seat Back Support Brackets & Vertical Supports [Page 1, Step 8]

Hardware Bag #4    Install Seat Back Cushion [Page 1, Step 12]

Hardware Bag #5    Install Seat Back Support Brackets to vehicle [Page 1, Step 5]

Hardware Bag #6    Install Seat Bottom Cushion [Page 1, Step 13]